29.4 Changing Your Mail Transfer Agent

Written by Andrew Boothman. Information taken from e-mails written by Gregory Neil Shapiro.

As already mentioned, FreeBSD comes with sendmail already installed as your MTA (Mail Transfer Agent). Therefore by default it is in charge of your outgoing and incoming mail.

However, for a variety of reasons, some system administrators want to change their system's MTA. These reasons range from merely wanting to try out another MTA to needing a specific feature or package which relies on another mailer. Fortunately, whatever the reason, FreeBSD makes it easy to make the change.

29.4.1 Install a New MTA

You have a wide choice of MTAs available. A good starting point is the FreeBSD Ports Collection where you will be able to find many. Of course you are free to use any MTA you want from any location, as long as you can make it run under FreeBSD.

Start by installing your new MTA. Once it is installed it gives you a chance to decide if it really fulfills your needs, and also gives you the opportunity to configure your new software before getting it to take over from sendmail. When doing this, you should be sure that installing the new software will not attempt to overwrite system binaries such as /usr/bin/sendmail. Otherwise, your new mail software has essentially been put into service before you have configured it.

Please refer to your chosen MTA's documentation for information on how to configure the software you have chosen.

29.4.2 Disable sendmail

Warning: If you disable sendmail's outgoing mail service, it is important that you replace it with an alternative mail delivery system. If you choose not to, system functions such as periodic(8) will be unable to deliver their results by e-mail as they would normally expect to. Many parts of your system may expect to have a functional sendmail-compatible system. If applications continue to use sendmail's binaries to try to send e-mail after you have disabled them, mail could go into an inactive sendmail queue, and never be delivered.

In order to completely disable sendmail, including the outgoing mail service, you must use


in /etc/rc.conf.

If you only want to disable sendmail's incoming mail service, you should set


in /etc/rc.conf. More information on sendmail's startup options is available from the rc.sendmail(8) manual page.

29.4.3 Running Your New MTA on Boot

The new MTA can be started during boot by adding a configuration line to /etc/rc.conf like the following example for postfix:

# echo 'postfix_enable=“YES”' >> /etc/rc.conf

The MTA will now be automatically started during boot.

29.4.4 Replacing sendmail as the System's Default Mailer

The program sendmail is so ubiquitous as standard software on UNIX® systems that some software just assumes it is already installed and configured. For this reason, many alternative MTA's provide their own compatible implementations of the sendmail command-line interface; this facilitates using them as “drop-in” replacements for sendmail.

Therefore, if you are using an alternative mailer, you will need to make sure that software trying to execute standard sendmail binaries such as /usr/bin/sendmail actually executes your chosen mailer instead. Fortunately, FreeBSD provides a system called mailwrapper(8) that does this job for you.

When sendmail is operating as installed, you will find something like the following in /etc/mail/mailer.conf:

sendmail	/usr/libexec/sendmail/sendmail
send-mail	/usr/libexec/sendmail/sendmail
mailq		/usr/libexec/sendmail/sendmail
newaliases	/usr/libexec/sendmail/sendmail
hoststat	/usr/libexec/sendmail/sendmail
purgestat	/usr/libexec/sendmail/sendmail

This means that when any of these common commands (such as sendmail itself) are run, the system actually invokes a copy of mailwrapper named sendmail, which checks mailer.conf and executes /usr/libexec/sendmail/sendmail instead. This system makes it easy to change what binaries are actually executed when these default sendmail functions are invoked.

Therefore if you wanted /usr/local/supermailer/bin/sendmail-compat to be run instead of sendmail, you could change /etc/mail/mailer.conf to read:

sendmail	/usr/local/supermailer/bin/sendmail-compat
send-mail	/usr/local/supermailer/bin/sendmail-compat
mailq		/usr/local/supermailer/bin/mailq-compat
newaliases	/usr/local/supermailer/bin/newaliases-compat
hoststat	/usr/local/supermailer/bin/hoststat-compat
purgestat	/usr/local/supermailer/bin/purgestat-compat

29.4.5 Finishing

Once you have everything configured the way you want it, you should either kill the sendmail processes that you no longer need and start the processes belonging to your new software, or simply reboot. Rebooting will also give you the opportunity to ensure that you have correctly configured your system to start your new MTA automatically on boot.